Is Male Plug (Small) compatible with ISO 80369

Quick Answer

Luer interfaces on the Male Plug (Small) (BHM-04) follow small-bore connector conventions; confirm exact ISO 80369 series compatibility for your application with Baixin Bio. It is molded from ABS for sealing and protecting luer ports.

Definition

A male plug (small) is one of the small standardized parts that make a medical fluid path work. Its job is to connect, seal or control flow between two segments of a line, and it is manufactured from device-qualified plastics for reliable single-use performance.

The component is small, but it carries real responsibility: a poor seal or an out-of-tolerance dimension can compromise an entire single-use assembly, which is why medical molders control material, tooling and process tightly.

It helps to picture where the part sits. A finished single-use device — an IV set, a transfer line, a dialysis circuit — is an assembly of molded plastic pieces joined into one fluid path. Each piece has a narrow job, and the value of standardization is that pieces from a catalog snap together predictably, so an assembler can design around known interfaces instead of bespoke fittings.

About This Component

The Male Plug (Small) is supplied as a single-use molded part for sealing and protecting luer ports. Its interface follows standard conventions so it mates predictably with compatible components, and it is produced in ABS by default, with other medical-grade resins available on request.

Like all Baixin Bio components, it can be customized for material, color, dimensions, packaging and assembly. For a precise specification — exact dimensions, tolerances, sterilization validation, packaging counts and minimum order quantity — request a drawing and samples through the inquiry form.

Key Advantages

Where male plug (small) earns its place, it is for a handful of practical reasons:

Leak-resistant seal that holds under normal line pressure
Single-use design that supports sterile, disposable workflows
Medical-grade resin selected for fluid compatibility
Dimensional consistency across production lots
Smooth fluid-contact surfaces for reliable connection

None of these advantages matter in isolation; their value is cumulative. A part that seals well but drifts dimensionally, or one that is consistent but slow to supply, fails the assembler. The point is to get all of them at once, reliably, lot after lot.

Common Applications

The settings that rely on male plug (small) include:

Enteral feeding sets
Laboratory fluid handling
Irrigation sets
Disposable diagnostic devices

The common thread is that every one of these settings needs junctions it can trust. A standardized, single-use component delivers that trust at scale: the same interface, the same seal and the same material behavior across an entire production lot, so the clinical team and the device maker are not relying on a one-off fitting at a critical point in the line.

How to Specify and Choose

A good specification answers a short list of questions up front:

Color coding or opacity requirements for the assembly
Packaging format and order volume for the program
The connection standard the mating part uses (luer slip, luer lock or a specific ISO 80369 series)
The working pressure the junction must hold without leaking or separating
The fluid and its chemical compatibility with the candidate resin

Getting these settled early means the first samples are usable and the program moves to volume faster. When a standard part does not fit, the same variables become the brief for an OEM or ODM tooling project.

Industry Standards

Two standards questions dominate this category: connection geometry and sterilization. Connection geometry is increasingly defined by the ISO 80369 series, which separates applications so incompatible lines cannot mate; sterilization is handled by validated EO, gamma or steam autoclave processes matched to the resin and the device.

For ABS components, the practical sterilization options are EO and gamma; the choice is confirmed against the finished device and its validated process.

Much of the modern standards work exists to prevent misconnection. Historically a single luer taper served many applications, which made cross-connections physically possible; the ISO 80369 series assign distinct geometries to different uses so incompatible lines simply will not mate. When you specify a connector, identifying the correct series for the application is therefore a safety decision, not just a fit decision.

This page is informational and does not replace device-specific regulatory or validation guidance. Confirm exact standards, biocompatibility and sterilization requirements for your product with your quality team and your supplier.

Frequently Asked Questions

What order volumes are supported?

Baixin Bio supplies disposable device assemblers in production volumes, with consistent lot-to-lot quality and export-friendly communication.

Can I request samples?

Yes. Samples and drawings are welcome and recommended before committing to volume. Use the inquiry form to request them.

Is male plug (small) available for OEM or ODM projects?

Yes. Baixin Bio manufactures to drawings and samples, customizing material, color, dimensions, packaging and assembly. Send your specification for a quote.

What materials are used?

Depending on the part, medical-grade PC, PP, PVC, ABS, PE or POM is used, selected for the connection method, fluid path and sterilization requirement.