The Flow Regulator (Small) (TS-001) suits IV infusion sets and tubing flow control and similar single-use fluid-handling assemblies. It is molded from ABS for dependable connections. Baixin Bio offers it as a standard or customized part.
Definition
The term flow regulator (small) refers to a precision component within IV infusion sets and tubing flow control. It defines how a fluid line connects, branches, seals or regulates, and it is molded to tight tolerances so the interface performs the same way across an entire production lot.
Because the part sits directly in the fluid path, three things matter most: a dependable seal, dimensional consistency from part to part, and a material that is compatible with the fluid and the chosen sterilization method.
To put it in context: a disposable fluid-handling device is rarely one molding. It is a chain of small components — connectors, valves, chambers, clamps, caps and tubing — assembled into a single path. Standard interfaces are what let those components come from a catalog and still fit, which is the whole reason this category of part exists.
About This Component
The Flow Regulator (Small) is supplied as a single-use molded part for IV infusion sets and tubing flow control. Its interface follows standard conventions so it mates predictably with compatible components, and it is produced in ABS by default, with other medical-grade resins available on request.
Like all Baixin Bio components, it can be customized for material, color, dimensions, packaging and assembly. For a precise specification — exact dimensions, tolerances, sterilization validation, packaging counts and minimum order quantity — request a drawing and samples through the inquiry form.
Key Advantages
Where flow regulator (small) earns its place, it is for a handful of practical reasons:
- Compatibility with common sterilization methods
- Standardized interface that interoperates with compliant luer components
- Leak-resistant seal that holds under normal line pressure
- Single-use design that supports sterile, disposable workflows
- Medical-grade resin selected for fluid compatibility
- Dimensional consistency across production lots
None of these advantages matter in isolation; their value is cumulative. A part that seals well but drifts dimensionally, or one that is consistent but slow to supply, fails the assembler. The point is to get all of them at once, reliably, lot after lot.
Common Applications
The settings that rely on flow regulator (small) include:
- Enteral feeding sets
- Laboratory fluid handling
- Irrigation sets
- Disposable diagnostic devices
- Syringe and pump connections
The common thread is that every one of these settings needs junctions it can trust. A standardized, single-use component delivers that trust at scale: the same interface, the same seal and the same material behavior across an entire production lot, so the clinical team and the device maker are not relying on a one-off fitting at a critical point in the line.
How to Specify and Choose
A good specification answers a short list of questions up front:
- Color coding or opacity requirements for the assembly
- Packaging format and order volume for the program
- The connection standard the mating part uses (luer slip, luer lock or a specific ISO 80369 series)
- The working pressure the junction must hold without leaking or separating
- The fluid and its chemical compatibility with the candidate resin
With those answers in hand, a supplier can confirm a standard part or scope a custom one without back-and-forth. Sharing a drawing or a physical sample removes the remaining ambiguity.
Industry Standards
From a compliance standpoint, the component sits at the intersection of connector standards and material standards. The ISO 80369 family governs small-bore connection geometry to prevent misconnection, while biocompatibility documentation and a validated sterilization route — EO, gamma or autoclave — establish that the molded material is acceptable for its intended contact.
For ABS components, the practical sterilization options are EO and gamma; the choice is confirmed against the finished device and its validated process.
Much of the modern standards work exists to prevent misconnection. Historically a single luer taper served many applications, which made cross-connections physically possible; the ISO 80369 series assign distinct geometries to different uses so incompatible lines simply will not mate. When you specify a connector, identifying the correct series for the application is therefore a safety decision, not just a fit decision.
This page is informational and does not replace device-specific regulatory or validation guidance. Confirm exact standards, biocompatibility and sterilization requirements for your product with your quality team and your supplier.
Frequently Asked Questions
What order volumes are supported?
Baixin Bio supplies disposable device assemblers in production volumes, with consistent lot-to-lot quality and export-friendly communication.
Can I request samples?
Yes. Samples and drawings are welcome and recommended before committing to volume. Use the inquiry form to request them.
Is flow regulator (small) available for OEM or ODM projects?
Yes. Baixin Bio manufactures to drawings and samples, customizing material, color, dimensions, packaging and assembly. Send your specification for a quote.
What materials are used?
Depending on the part, medical-grade PC, PP, PVC, ABS, PE or POM is used, selected for the connection method, fluid path and sterilization requirement.
How is it sterilized?
Components are compatible with validated single-use sterilization such as ethylene oxide, gamma irradiation or steam autoclave, depending on the resin. Confirm the method for your device.
Related Products
Related Questions
Explore More
Need Medical Connectors or Components?
Baixin Bio manufactures luer connectors, valves, drip chambers, clamps, caps and tubing, with OEM and ODM customization. Send your drawings or samples for a quote.
Request a Quote