What is Long Spike used for

Quick Answer

The Long Spike (CV-006) is a medical plastic component used in IV sets, drip flow control and bag or bottle access. It provides a secure, single-use connection in the fluid path and is molded from ABS. Baixin Bio supplies it in standard form and with OEM/ODM customization.

Definition

A long spike is one of the small standardized parts that make a medical fluid path work. Its job is to connect, seal or control flow between two segments of a line, and it is manufactured from device-qualified plastics for reliable single-use performance.

The component is small, but it carries real responsibility: a poor seal or an out-of-tolerance dimension can compromise an entire single-use assembly, which is why medical molders control material, tooling and process tightly.

It helps to picture where the part sits. A finished single-use device — an IV set, a transfer line, a dialysis circuit — is an assembly of molded plastic pieces joined into one fluid path. Each piece has a narrow job, and the value of standardization is that pieces from a catalog snap together predictably, so an assembler can design around known interfaces instead of bespoke fittings.

About This Component

The Long Spike is supplied as a single-use molded part for IV sets, drip flow control and bag or bottle access. Its interface follows standard conventions so it mates predictably with compatible components, and it is produced in ABS by default, with other medical-grade resins available on request.

Like all Baixin Bio components, it can be customized for material, color, dimensions, packaging and assembly. For a precise specification — exact dimensions, tolerances, sterilization validation, packaging counts and minimum order quantity — request a drawing and samples through the inquiry form.

Key Advantages

For device assemblers specifying long spike, the benefits that matter most are reliability and repeatability:

Leak-resistant seal that holds under normal line pressure
Single-use design that supports sterile, disposable workflows
Medical-grade resin selected for fluid compatibility
Dimensional consistency across production lots
Smooth fluid-contact surfaces for reliable connection

None of these advantages matter in isolation; their value is cumulative. A part that seals well but drifts dimensionally, or one that is consistent but slow to supply, fails the assembler. The point is to get all of them at once, reliably, lot after lot.

Common Applications

Typical applications for long spike span the disposable device landscape:

Irrigation sets
Disposable diagnostic devices
Syringe and pump connections
IV infusion sets

What links these applications is risk. Each one moves fluid into or out of a patient or a sample, so a leak, a wrong connection or a contaminated surface has consequences. Standardized single-use components reduce that risk by making every junction predictable and by being discarded rather than reprocessed, which is the safer default for most modern disposable devices.

How to Specify and Choose

Specifying the right part is mostly about matching a handful of variables to your assembly:

The connection standard the mating part uses (luer slip, luer lock or a specific ISO 80369 series)
The working pressure the junction must hold without leaking or separating
The fluid and its chemical compatibility with the candidate resin
The inner and outer diameters of the tubing the part bonds to
The sterilization method the finished device will undergo

With those answers in hand, a supplier can confirm a standard part or scope a custom one without back-and-forth. Sharing a drawing or a physical sample removes the remaining ambiguity.

Industry Standards

Two standards questions dominate this category: connection geometry and sterilization. Connection geometry is increasingly defined by the ISO 80369 series, which separates applications so incompatible lines cannot mate; sterilization is handled by validated EO, gamma or steam autoclave processes matched to the resin and the device.

For ABS components, the practical sterilization options are EO and gamma; the choice is confirmed against the finished device and its validated process.

Much of the modern standards work exists to prevent misconnection. Historically a single luer taper served many applications, which made cross-connections physically possible; the ISO 80369 series assign distinct geometries to different uses so incompatible lines simply will not mate. When you specify a connector, identifying the correct series for the application is therefore a safety decision, not just a fit decision.

This page is informational and does not replace device-specific regulatory or validation guidance. Confirm exact standards, biocompatibility and sterilization requirements for your product with your quality team and your supplier.

Frequently Asked Questions

How is it sterilized?

Components are compatible with validated single-use sterilization such as ethylene oxide, gamma irradiation or steam autoclave, depending on the resin. Confirm the method for your device.

Is it compatible with ISO 80369?

Luer interfaces follow small-bore connector conventions. Confirm exact ISO 80369 series compatibility for your application with Baixin Bio before specifying.

What order volumes are supported?

Baixin Bio supplies disposable device assemblers in production volumes, with consistent lot-to-lot quality and export-friendly communication.

Can I request samples?

Yes. Samples and drawings are welcome and recommended before committing to volume. Use the inquiry form to request them.

Is long spike available for OEM or ODM projects?

Yes. Baixin Bio manufactures to drawings and samples, customizing material, color, dimensions, packaging and assembly. Send your specification for a quote.